Blog

Learn When to Paint

Following these suggestions will help you accomplish the quality paint task you seek. When you have completed, you will have the gratifying experience of stepping back and appreciating your helpful work.

When to paint

The temperature level of your house influences the efficiency of paint. The wall temperature level should be above 10C throughout the painting process. You need to generally stay clear of painting in incredibly hot or cold conditions.
If it appears like rain, bear in mind the painter’s guideline; if you wouldn’t hang the washing out or wash the car, do not paint! Nothing is more frustrating than seeing your work ruined!

Making use of acrylics in heat

The best weather condition in the summertime months will increase this drying process due to the fact that the majority of acrylics are touch dry in twenty minutes at 25 degrees and 50 % humidity. To decrease the drying out rate, Dulux Hot Weather Thinner might be contributed to the paint at the rate of 50ml per litre. A good pointer for painting in summer season is not to paint in direct sunlight or onto a hot surface. Attempt to follow the shade where possible. You can add up to approx 5 % water. Utilizing 2 brushes – keeping one in a container of water and rotating them, stops them drying out.

Picking enamels or acrylics for exterior use

We would generally suggest using acrylics in exterior circumstances. As enamels age they become milky and very breakable and therefore have a tendency to crack and flake off the surface. On the other hand, acrylics maintain their color better, do not chalk to any wonderful extent and do not get brittle, giving a longer long lasting, more long lasting paint finish.

The higher adaptability and UV security of Dulux Weathershield is the favored choice. Dulux assurances Weathershield for as long as you live in your house. That’s the Dulux Promise.

Moving and Removing

If you haven’t currently doinged this, take down curtains, mirrors and photos. Move lightweight furniture from the space. Cover staying furnishings with plastic sheets or drop cloths and tape plastic around pendant light fittings. Or if painting outside tie back plants so you have clear access to the locations to be painted.

Concealing

Painting will be quicker and cleaner if you mask. Get rid of masking tape or documents before the paint is too dry as removal later on can lift and break the dry paint leaving a split and jagged edge.

The Painting Sequence
Begin at the top and work down, this means beginning with the ceiling. Paint away from the light so you are not painting in shadow. Next paint the walls, then the windows and doors, followed by the skirting and the trim.
Weatherboards are painted in 2 phases. Paint the underside of the board initially then paint the face. Paint numerous boards at a time then move your ladder over and continue along the remainder of the wall.

Mixing is Vital
Before applying paint; make sure you stir it well according to the directions on the can. Always ‘box’ your paint; i.e. if you are utilizing more than one can, tip the components of each into a bigger container, like a huge plastic container, and stir completely. You can then put it straight into your painting pot, or refill the initial tins for future use.

Brushing
Prior to use, moisten the brush in water if you will use a water-based paint, or turps if you are about to make use of an oil-based paint. See to it you get rid of excess fluid prior to painting.
Fill the brush by dipping in up to half the length of the bristles.
Tap it delicately against the side of the can: do not clean the brush hard against the lip. The bristles should bend just somewhat as you brush – don’t over press – let the paint flow from the brush.
If you are painting a big location by brush, apply paint to an area about 50 cm X 50 cm, then brush the paint in horizontal strokes to even the paint out and finish off with light vertical strokes all in one instructions.
Paint the edges of the area first if you are utilizing a brush and roller. Painting window frames, skirtings, mouldings and doors are worth doing very carefully to obtain the best outcomes. Constantly work in areas and paint up to a natural break before stopping. Begin on top and work down, painting with light even strokes, working back into the wet edge.
Never attempt to paint over an area that is partially dried out, as the brush will leave marks in the surface. Paint over it as soon as possible with light even strokes if you see a run in the wet paint.

Rolling
To utilize a roller you’ll require a tray, frame, roller cover and possibly an extension pole. Make certain you have the right roller for the task. Generally speaking, 6-8mm nap covers are used for semi and gloss gloss paints, 10-12mm nap pays for reduced shine and flat paints on walls and 20-32mm nap covers for many paints on rough surfaces like concrete or textured walls.
Fit the roller to the frame. Pour paint into the tank at the end of the roller tray. Do not overfill. Dip the roller gently into the paint, then roll it gently backwards and forwards on the ramp to equally disperse the paint on the roller cover. Slowly roll the paint onto the surface in a series of close zig-zag strokes. When the paint starts to run, re-roll the location with parallel strokes to even the spread.
Never leave a paint-covered roller exposed to the air for any length of time. Wrap it in plastic cling wrap when you take a short break, and make certain to scrubbing it entirely after use.

Paint Application Pads
Application pads can be made use of for cutting in where there are lots of edges to paint around. Just pack the pad with paint utilizing a paintbrush. Place it on the wall, examining the guide wheels are clean, run the wheels along the architrave, skirting or edge.

Tidying up
If you are preparing to continue the work the next day, simply keep the paint, brush and/or roller in the paint tray and cover with foil or cling wrap. The next morning, run the brush or roller over a paper a couple of times and it will prepare to utilize.
After the job is finished wash the rollers and brushes and paint tray with water for water-based paints or mineral turps for solvent-based paints. Do not use a spinning tool to clean brushes, as this will make your brush flare.
Excess paint can be saved in the can. Water-based paints can be treated with Dulux Envirosolutions Waste Paint Hardener. For the disposal of larger quantities of paint, contact your regional council.

Paint away from the light source so you are not painting in shadow. Paint the underside of the board first then paint the face. Generally speaking, 6-8mm nap covers are made use of for gloss and semi gloss paints, 10-12mm nap covers for low sheen and flat paints on walls and 20-32mm nap covers for the majority of paints on rough surfaces like textured or concrete walls.
Dip the roller lightly into the paint, then roll it carefully backwards and forwards on the ramp to uniformly disperse the paint on the roller cover. After the task is completed clean the rollers and brushes and paint tray with water for water-based paints or mineral turps for solvent-based paints.